Author Topic: Setting the timing  (Read 1655 times)

0 Members and 1 Guest are viewing this topic.

rohnk

  • Guest
Setting the timing
« on: March 30, 2012, 08:54:48 AM »
When setting the engine timing, which way do you rotate the distributor? Clockwise for advance and counter-clockwise to retard?

I've not done timing in probably 20 years so forgive my ignorance! I know I have to lossen the bolt to allow the distributor to turn just don't know which way to go with it.

Tried starting my Eagle last night after compleing the motorcraft swap. I haven't done the ECM Test yet becuase I wanted to get it running before I do that step.

Offline doc65

  • Eagle DL
  • ***
  • Posts: 252
  • Thumbs Up 6
  • Ogden, UT
Re: Setting the timing
« Reply #1 on: March 30, 2012, 09:08:38 AM »
Negative, advance is always the oposite of the rotation of the rotor, so in this case counter-clock to advance & clockwise to retard.

Offline thereverendbill

  • The Mobile Body Guy
  • AMC Eagle Nest Addicted
  • ********
  • Posts: 2330
  • Thumbs Up 81
  • Immune to rust
Re: Setting the timing
« Reply #2 on: March 30, 2012, 11:31:27 AM »
if my memory serves me correctly you need to bypass the ECM before you set the timing
1980 Eagle 2 door sedan (future solid axle swap)
1981 Eagle Kammback (restoration in progress)
1983 SX/4 SOLD
1983 Eagle Limited wagon  *For Sale* SOLD
Click for YOUR TOWN, STATE Forecast" border="0" height="100" width="150

another amc forum
www.amcevolution.com

Offline eagle503

  • "I'm not a mechanic I'm a parts replacer give me the book I can do it"
  • Eagle DL
  • ***
  • Posts: 254
  • Thumbs Up 12
  • 85 limited wagon
    • art of loehr
Re: Setting the timing
« Reply #3 on: March 30, 2012, 11:46:33 AM »
You wont get it running until you do the ecm test. The computer is trying to retard - advance the timing in accordance with the signal from the stepper and sensors. It will probably start once then die and just try to turn over from there.
Click for YOUR_TOWN, STATE Forecast" border="0" height="100" width="150


rohnk

  • Guest
Re: Setting the timing
« Reply #4 on: March 30, 2012, 12:09:05 PM »
Ok, I'll ECM Test it tonight and see what happens. I have read where other guys had started and driven there's before doing the ECM Test.

Offline kajsdf

  • Eagle DL
  • ***
  • Posts: 168
  • Thumbs Up 8
Re: Setting the timing
« Reply #5 on: April 05, 2012, 09:58:38 PM »
i didbut it ran only well enough to back out of the garage and die. you really need to do the bypass before setting timing. it is very easy, just be sure you follow the instructions carefully
1985 eagle wagon limited
now more limited...
2150 swap...tf727/np229 swap...258 megabuild in the works...

rohnk

  • Guest
Re: Setting the timing
« Reply #6 on: April 06, 2012, 06:29:33 AM »
Update for this thread.

I was information that on my 82 model ICM, there are three plugs coming from it. Since I am already wired directly from ICM to distributor, I had to disconnect the third plug with a yellow and black wire on it. Then short the yellow and black together. This takes the ECM out of the loop for timing control.

Slightly different than a ECM Test BYPASS on the two plug ICM's where you have to cut and wire the distributor directly to the ICM.

Moderator, can this be a sticky? Seems like good knowledge to keep shared. I learned it from another nest member so I cannot take credit, but I think this beongs someplace where others can find it easy.

steveabn8295b

  • Guest
Re: Setting the timing
« Reply #7 on: April 06, 2012, 10:24:36 AM »
set sticky

 

Sporadic Ignition Timing when the Engine's at Temp

Started by FreedomMachine

Replies: 19
Views: 2002
Last post March 27, 2012, 01:12:07 AM
by ammachine390
timing after mcu bypass test

Started by jim

Replies: 7
Views: 1662
Last post September 07, 2011, 08:56:39 PM
by jim
timing

Started by sammuel

Replies: 15
Views: 1555
Last post February 29, 2012, 03:47:26 PM
by sammuel
Setting spark timing

Started by mr.mindless

Replies: 7
Views: 872
Last post February 16, 2012, 09:00:34 AM
by shaggimo